*ER9000 Opt. 00: 10 Hz – 30 MHz
*ER9000 Opt. 01: 10 Hz – 3 GHz
*Very fast FFT scan gapless (2 sec. In Band B, 1 min. In Band C + D)
*Color Touch-Screen Display
*Compliant with CISPR 16-1-1, MIL-STD-461, ANSI C63.2 and FCC
*Compliant with CISPR 14-1 in combination with the Click CA0010 extension
*Lightning-fast full-compliant scanning
*Integrated CISPR pulse generator
*Robust and compact construction, battery operated and with AC / DC power supply
*Free PES (PMM Emission Suite) software with advanced EMC functionality

*9 kHz to 30 MHz frequency range
*Up to 300 A (continuous); 500 A (20 min.) rated output current
*Suitable for DC to 60 Hz power lines
*Built-in, selectable 250 μH coil (choke)
*Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15, MIL-STD 461F
*Fan air cooling
*Stackable up to four units in wheeled rack (see data sheet L3-500)
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

CISPR 16-1-1 full compliant
Built-in LISN
Gapless FFT
Single input connector
Up to 2W max input power
Low distortion preamplifier

*Full CISPR 16-1-1 compliant 9 kHz - 30 MHz
*FFT-based, gapless EMI receiver and analyzer, 10 Hz – 30 MHz
*Reduces test time from hours to seconds
*User-friendly in stand-alone and with the powerful PMM Emission Suite software

*Modular approach for all budgets
*Full compliance to CISPR 16-1-1 and MIL-STD
*Eliminates long coax cables
*Compact, lightweight, battery operated
*Features all new detectors

*Discontinuous disturbance (click) analysis
*Four independent frequency channels measuring simultaneously
*Each channel with embedded preselector, attenuator and preamplifier
*Designed to fully match CISPR 16-1-1 and CISPR 14-1 Standards
*Highly flexible selection of number of rates, quartiles and runs operating mode
*Test duration reduced to the minimum theoretically achievable
*Built-in two-lines 16A Line Impedance Stabilization Network (LISN)
*User port for driving any external LISNs
*Embedded switch operation counting unit
*CISPR 16-1-1 embedded click and pulse generator output for internal or external use
*Autocheck and calibration
*Stand alone or PC driven operations
*Free PCA PMM Click Analysis software
*Free PCG PMM Click Generation software
*Full IF and QP history 500us resolution
*Compact yet sturdy construction
*140 dBμV (2 W) maximum input level without damage

*9 kHz to 30 MHz frequency range
*Antenna CISPR 12, CISPR 16, CISPR 25, MIL-STD, DO-160 fully compliant
*Internal full CISPR 16-1-1 receiver
*Operates both swept and gapless FFT modes
*Very fast measuring time
*Embedded attenuator, preamplifier and preselectors
*Fiber optic serial link to 9010F series or directly to PC
*Grounding effectiveness auto-diagnostic capability
*On-board tracking generator and antenna CISPR adapter
*Automatic diagnostic and calibration
*Scattering free
*PC software
*RF front-end output
*On-board capacitance meter
*Plug-in rechargeable Li-ion battery

*L1-150M: 100 kHz to 200 MHz frequency range
*L1-150M1: 10 kHz to 400 MHz frequency range
*Multi standard design
*150 A max output current
*Suitable also for DC lines
*Large baseplate for optimal grounding
*Robust, compact construction
*Screw terminals for safe wiring
*Meets the requirements of several standards including CISPR 16-1-2, CISPR 25, ISO 11452-2/4/5, ISO 7637-2, MIL-STD-461F
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

*5 kHz to 26,5 GHz frequency range
*Up to 66 dB dynamic, single range
*Symmetrical dipole configuration
*Excellent isotropy (down to 0,2 dB typical)
*Up to 40 meters communication by Fiber Optic Cable
*Up to 80 hours of operation before recharging
*High performance, high reliability Li-Mn battery
*PC direct connection via Optical to RS232/USB
*Extremely lightweight: 22 g only!

*9 kHz to 30 MHz frequency range
*Up to 16 A continuous rated output current
*Suitable for DC to 60 Hz power lines
*Built-in, selectable 150 kHz high pass filter
*Artificial Hand circuit
*Local and remote control from PMM EMI receivers
*Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15, MIL-STD 461F
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

*9 kHz to 30 MHz frequency range
*Up to 32A continuous rated output current
*Built-in, selectable 150 kHz high pass filter
*Artificial Hand circuit
*Suitable for DC to 60 Hz power lines
*Local and remote control from PMM EMI receivers
*Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15, MIL-STD 461F
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

*9 kHz to 30 MHz frequency range
*Up to 60/63 A continuous rated output current
*Suitable for DC to 60 Hz power lines
*Local and remote control from PMM EMI receivers
*Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15, MIL-STD 461F
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

*9 kHz to 30 MHz frequency range
*Up to 60/63 A continuous rated output current
*Suitable for DC to 60 Hz power lines
*Local and remote control from PMM EMI receivers
*Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15, MIL-STD 461F
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

*9 kHz to 30 MHz frequency range
*Up to 100A continuous rated output current
*Local and remote control from PMM EMI receivers
*Suitable for DC to 60 Hz power lines
*Meets the requirements of several standards including CISPR 16-1-2, VDE 0876, FCC part 15, MIL-STD 461F
*Powering the EUT
*EUT termination to a standardized impedance with respect to ground
*Couples the measuring receiver to the disturbance generated by the EUT
*Decouples the measuring receiver from unwanted RF signals from the power line

Fully compliant to: CISPR 16-1-2
Attenuation 35 dB

Fully compliant to: CISPR 16-1-2
Attenuation 30 dB